hayward flow switch troubleshooting

The Control checks for a closed Blower Vacuum Switch. Abandon existing switch for Hayward R-22 heat pumps.

How To Replace A Hayward Aqua Rite Flow Switch Chlorine King Pool Service Youtube

Arrows at the top of the hex nut need to point in the direction of water flow.

. There should be no elbow pipe after the flow switch. Displaying HOT or COLD _ 37-38 Additional Information. Here youll gain easy access to information regarding your favorite Hayward products.

Installs in flow switch tee 401-247 Manufactured by Harwil and comes with a 15ft cord. Max Switching Current DC 04A. The minimum rated flow rates are listed on page 13 of this manual.

Green the above mentioned status indicates that your flow switch is stuck in close position or the wire is shorted andor the wire connections to the RJ11 modular phone connector is shorting out. Check Salt Inspect Cell. Max Carry Current 10A.

HAYWARD To switch Cell Type cycle Main Switch from AUTO- super Chlorinate AUTO. Darrin - If you held the switch contacts closed for 60 seconds and the No Flow LED did not go off your new switch may be bad. Should be no elbow after the flow switch.

LED ON 21-25 3. If it is not open disconnect the cable and wait for six seconds. The Igniter is de-energized at flame sense or at completion of 4 sec trial.

Hayward Flow Control has been a leading manufacturer of industrial thermoplastic valves and process control products for more than 60 years. SPST contact Rating 10W Max. When it comes to troubleshooting Hayward pool heaters theres not too much difference between the problem solving process for other gas-fired heaters made by Jandy Pentair or Raypak.

Continuity is open if there is no flow. The flow switch requires a minimum flow rate of 11 GPM to consistently stay closed. 39-44 Cell Compatibility Chart Salt Addition Table 40-41.

For Summit and Hayward R-410A units replace existing screw on LP switch with new. You can test the continuity of the flow switch using a Voltmeter or Ohmmeter. February 24 2015.

That test bypasses tests for low flow and arrows installed wrong. While you are checking the valve position check the valve to make sure there are no obstructions. Then give Hayward a call at 866-772-2100 to see what they say.

NOTE 4 Blue LP wires. Test your system and if necessary adjust the water pressure switch as described on page 32 of this manual. Set scale on meter to lowest.

If you have questions regarding troubleshooting a problem installing this flow switch call 1-888-921-7665 for Technical support. 6 month manufacture parts only warranty when purchased through a Hayward Authorized Online Reseller. GLX-FLO-RP Flow switch is factory original The GLX-FLO-RP screw into your existing tee and comes with a 15 cord.

Hayward Aqua Rite Troubleshooting Guide. LED flashing or ON 26-30 4. Display ONLY Lights ONLY or Neither 31-36 5.

Since then we have remained committed to producing the highest quality products while providing outstanding service. No Flow LED will be ON when there is a flow switch problem. If you need help troubleshooting the device read our helpful guide with the most frequently asked questions and answers.

At proper Igniter temp a 4 second trial begins. Some installations may require an adjustment to the water pressure switch for proper low-flow protection. Super Chlorinate Auto Off Super Chlorinate Auto.

Gas valve opens and monitors flame sense. The arrows at the top of the hex nut need to point in the same direction as the water flow. 42 out of 5 stars.

No Flow LED will flash for up to 60 seconds on start-up. Briidea Flow Switch Flow Sensor with Tee for Hayward Salt System Compatible with Hayward Goldline System. Troubleshooting flow charts.

Replacement switch is a screw on switch. No LEDsLCD display verify 220-240 VAC or 115-125 VAC. Troubleshooting Guides To view these documents you will need to download the free Acrobat Reader which gives you instant access to PDF files.

Power Generating Super Chlorinate Remotely Controlled -r No Flow Cheek Salt High Salt nSpect Cell If LED is ON check for flow switch installed backward. If the No Flow LED is ON check if the flow switch is installed backward. Whether you are looking for a Quick Reference Guide troubleshooting steps or simply wish to view one of our product support videos you have come to the right place.

Hayward Goldline SuperPro Flow Switch Salt Generator Systems Q12DS156MNO3A. Remove and connect multimeter to wire ends and measure Ohms reading. The Hayward Aqua Trol is a saltwater generator for above ground pools.

If the flame is sensed The Blower Vacuum Switch Control Loop Temp. In fact Hayward was one of the originators of the first thermoplastic ball valves. The components of a Hayward pool heater are also very similar to gas heaters made by other manufacturers.

The blower will turn off for one second. Check that the flow line is plugged all the way into the control box. Flashing or ON 17-20 2.

Use a swivel tee on the low side access port. Ensure the flow switch valve is open. Flow Switch for Hayward Salt Chlorine Generator GLX-FLO-RP with 15-Feet CableFlow Sensor with Tee Replacement Kit Suitable for Hayward Salt System 47.

The majority of our literature and brochures are in English only. Plug the cable back in and check the valve again. If there is adequate flow and the LED is still on check that the arrows on the flow switch on top of hex are pointing in the direction of flow.

Spark Ignition Pool Heater Troubleshooting Guide Pool Heater Pool Heater